News

Are your truck's running board mats worn, cracked, or smooth from age? Worn running board mats aren't just unsightly; they can also pose a safety hazard. Installing new running board mats is one of the easiest and most affordable upgrades to improve the safety and appearance of your truck. You don't need to be a skilled mechanic or have a garage full of tools to do it. In this guide, we'll walk you through the entire process, from preparing the surface to finally pressing the step pads into place. Let's roll up our sleeves and get your truck steps back in tip-top shape! What You'll Need: Tools & Materials Having your tools ready before you begin is key to a smooth installation. Here's your checklist: New Running Board Step Pads: Ensure you have the correct set for your truck's make, model, and running board type. Rubbing Alcohol or Adhesive Promoter: For a crucial final clean. Microfiber Cloths: Lint-free is best. Plastic Pry Tool or Soft Putty Knife: To safely remove old pads. Heat Gun or Hair Dryer: Highly recommended for loosening old adhesive. Adhesive Remover: For cleaning off old residue. Safety Glasses and Gloves: Protect your eyes and hands. Masking Tape (Optional): For temporarily holding pads in place during alignment. A Bucket of Soapy Water (Optional): For general initial cleaning. Step 1: Removing the Old Truck Step Pads This is often the most time-consuming part, but patience is essential. 1. Heat: Using a heat gun or hair dryer, heat the old truck step mat at medium heat. Gently apply heat back and forth along an area of the mat for 60-90 seconds. This will soften the underlying adhesive, making removal easier and reducing the likelihood of residue. 2. Pry off a corner: Once the mat is warm, carefully insert a plastic pry tool under one corner of the mat. Metal tools may scratch the step, so using a plastic tool is highly recommended. 3. Peel slowly and steadily: Move slowly down the mat, increasing the heat as needed. Pull the mat back at a 45-degree angle, rather than straight up. If you encounter significant resistance, stop and continue heating. Step 2: The Critical Cleaning & Prep Stage The lifespan of your new pedal pads depends entirely on this step. Any residual grease or adhesive will prevent a secure bond. 1. Removing residual adhesive: There may be residual adhesive on the pedals. Apply a generous amount of Goo Gone or a specialized adhesive remover and let it sit for several minutes to break down the adhesive. 2. Scraping: Use a plastic scraper to scrape away any softened residue. Wipe the surface clean with a paper towel. 3. Final Wipe: This is the most important cleaning step. Dampen a clean microfiber cloth with rubbing alcohol, or use a prepackaged adhesive promoter. Thoroughly wipe the entire surface of the new pedal pad. The alcohol will remove any remaining oil, ensuring a clean, clear surface ready for adhesion. After wiping, do not touch the surface with bare hands. Step 3: Dry Fitting Your New Running Board Step Pads Before you peel off any backing, always do a dry fit. 1. Align the pedal pads: Take your new pedal pads and carefully place them on a clean pedal board. 2. Check for perfect alignment: Make sure they are straight and centered. Pay close attention to any protrusions or alignment tabs. This is your opportunity to make adjustments without making any commitments. 3. Use masking tape (optional): If you're working alone or in strong winds, you can use a small piece of masking tape to temporarily secure the pedal pads in place once you're satisfied with the alignment. Step 4: The Installation - Patience is Power Now for the main event! 1. Remove the backing: Starting at one end of the mat, slowly peel back approximately 6-12 inches of the protective backing from the tape. 2. Align and press: Carefully align the exposed adhesive section with the location you marked or taped. Once perfectly aligned, press firmly across the entire exposed section. 3. "Peel and Stick" method: Slowly continue peeling back the backing while pressing the mat onto the pedal with your other hand. Use the heel of your hand to apply even pressure. 4. Apply final pressure: Once the entire mat is in place, check the entire surface again and apply firm pressure for at least 30-60 seconds. You can even stand on it (if safe) to ensure a completely secure bond. Step 5: The Final Cure and Enjoyment 1. Let it sit: For the strongest possible bond, avoid using the brake pads for at least 0-48 hours. If possible, let it sit for 48 hours before frequent use or cleaning. 2. Admire your work: Stand back and look at your truck. You've just significantly improved its safety and appearance with your own two-handed hands, and saved a ton of money in the process! Pro Tips for a Perfect Finish Apply in Warm Weather: If possible, install in warm weather (above 60°F/15°C). Higher temperatures make the adhesive more flexible and stickier. Don't rush the heat: When removing old running board step pads, applying heat too quickly can cause them to melt, creating a mess. Low and slow heat is the best method. Replace one side at a time: If you're replacing the running board step pads on both sides of your truck, complete the replacement on one side first, starting from the beginning and ending, before moving on to the other side. This will provide a fresh reference point.

EVA foam boat flooring outperforms traditional materials with superior durability, waterproofing & slip resistance. Discover how Hjdeck's engineered marine-grade foam creates lasting protection.

In the field of EVA foam marine flooring, the choice of adhesive is crucial, as it must withstand the harsh marine environment, including continuous exposure to water, UV radiation, temperature fluctuations, and mechanical stress. 1. Primary Bonding: Panel Splicing and Flooring Installation This is the most critical application, creating a permanent, waterproof bond between EVA panels or between EVA and the ship's deck. Adhesive: Polyurethane Contact Adhesive Use Case: Splicing: Bonding the edges of individual EVA foam panels together to create a seamless, continuous flooring surface. Full Installation: Permanently bonds large EVA flooring panels to boat decks (typically fiberglass, aluminum, or painted wood). 2. Surface Lamination and Minor Repairs Adhesive: Specialty EVA Adhesive/Water-Based PU Adhesive Use Case: Bonding the top decorative layer or non-surface layer to the E-foam substrate during manufacturing or on-site repairs. Small, localized repairs on pre-installed flooring. 3. Sealing and Edge Work Adhesive: Polyurethane Sealant or MS Polymer Sealant Use Case: Sealing Perimeter: Filling the gap between the edge of the EVA flooring and the boat's gunwales, hatches, or other fixtures to create a watertight seal and prevent debris from getting underneath. Seam Reinforcement: Adds waterproof beads to critical seams for enhanced safety Reasons to Use: Highly Resilient: Can stretch and compress during vessel movement without cracking. Excellent Weather/UV Resistance: Withstands harsh marine environments without breaking. Adhesion: Provides strong bonds to EVA, fiberglass, and metal. The Key Role of Primer Product: Plastic and Elastomer Primer (e.g., 3M Primer 94) Use Case: Apply to boat deck surfaces before installing EVA foam flooring. Why Essential: Dramatically Enhances Adhesion: Creates a strong secondary bond, ensuring maximum performance of the primary adhesive.   Additional Resources: How to Install Hjdeck? How to Remove Hjdeck Boat Flooring Adhesive? Custom Features

We recently received excellent feedback from a satisfied customer who upgraded their 2005 35 Yacht with our HJDeck ocean decking in Medium Grey + White with Teak Stripe: "Thanks, Eric, everything went smoothly. I absolutely love this product. One of the posts on the grill side pad wasn't cut to match the left post as shown in the photo. I did my best to cut along the post. It looks really good overall - thank you! I will recommend your company if I need a replacement in the future, or to others who appreciate this product." This customer testimonial highlights the elegance, durability, and customization of our ocean decking solutions. If you're looking to upgrade your yacht's deck to a sleek, modern look, our HJDeck line is the perfect choice! Custom-Cut Decking for a Perfect Fit Custom Template Service – Send us your measurements and we'll customize your deck to ensure a perfect fit. Fast and Reliable Shipping – No more waiting; get your deck quickly and efficiently. Referral Discount – Love our products? Refer a friend and earn a reward! Upgrade your yacht deck today! Give your 2005 35 yacht (or any boat) a brand-new look with premium HJDeck marine flooring. For the same product, please click: 2003-2010 Silverton 35 Motor Yacht Cockpit & Swim Deck Pad EVA Foam Boat Flooring Click Here to Explore HJDeck Marine Flooring!

If you own a 2004 Regal 2000 VBR, you know the importance of keeping your boat in top condition. One of our satisfied customers recently shared their experience: "We're very pleased with the product. Like I said before, you recommended ordering full-boat carpeting, and now we're looking to order a complete interior carpeting package—just like our previous model." This feedback highlights the quality, fit, and comfort of our custom marine carpeting. If you're looking to upgrade your boat's interior, now's the time! Exclusive Offer: Faster Shipping and Special Discounts We understand how frustrating shipping delays can be. That's why we offer the following: ✅ Expedited Shipping Options—No more waiting 5 weeks! Get your carpeting faster. ✅ Limited-Time Discount—Special Offer on Full-Boat Carpeting Orders ✅ Perfect Fit Guarantee – Designed specifically for the 2004 Regal 2000 VBR. Why Boat Owners Love Our Custom Carpeting ✔ Superior Durability – Waterproof, mildew-resistant, and UV-resistant.✔ Custom Fit – Precision-cut for seamless installation.✔ Enhanced Comfort – Soft yet durable, comfortable even under bare feet.✔ Easy Care – Stain-resistant and easy to clean. For the same swim platform pads, please click: Regal 2000 Model 2003-2016 EVA Foam Boat Deck Mat Flooring Swim Platform Pads For the same Complete Kit, please click: 2003-2016 Regal 2000 EVA Foam Teak Boat Flooring Marine Decking Kits Browse our boat flooring kits: https://www.hjdeck.com/collections/boat-kits Have questions? Contact us today!

HJDeck prides itself on providing high-quality marine flooring solutions that enhance both the look and functionality of a vessel. We've recently received fantastic feedback from one of our customers who installed our swim platform kit on their 2014 Sea Ray 240 sundeck! Project: Stylish, Non-Slip Swim Platform Upgrade This customer was looking for a durable, stylish, and non-slip flooring solution for their swim platform. Choosing HJDeck marine flooring, they found the installation process to be smooth and the results to be excellent. What they said? "The swim platform kit works perfectly and looks great!" After installation: Before installation: Why choose HJDeck? ✔ Superior Durability – Made with high-density, 3000+ hour UV-resistant material, it withstands sun, saltwater, and frequent foot traffic. ✔ Superior Grip – Customized non-slip texture ensures safety even in wet conditions. ✔ Custom Fit – Precision-cut kits for seamless installation. ✔ Aesthetic Upgrade – Enhance your boat's exterior with clean, modern styling. Ready to upgrade your boat? Whether you own a Sea Ray, Bayliner, or any other boat, HJDeck has the perfect marine flooring solution. For the same product, please click: 2010-2015 Sea Ray 240 Sundeck EVA Foam Faux Teak Boat Flooring Custom Boat Kits Browse our boat flooring kits: https://www.hjdeck.com/collections/boat-kits Have questions? Contact us today!

We love hearing feedback from our clients, and this recent review of a 2013 Monterey 224 FSC in Dark Grey/Black put a smile on our faces! The customer shared that they’re extremely happy with the installed foam deck pads, calling it a "great job overall." While there were a few minor adjustments needed, the experience was overwhelmingly positive—something we always strive for. At Monterey Boats, we’re committed to quality and customer satisfaction, whether it’s a new purchase or an upgrade. If you’re considering a Monterey 224 or any customization, we’d love to help make your experience just as smooth. Have questions or need details on how we ensure perfection? Contact us—we’re here to help! Stay tuned for more customer stories and boating tips!

Why Do You Need a Professional Water Sports Board Mat? Whether it is surfing, paddle boarding or other water sports, a good board mat can not only improve your grip stability, but also make you more comfortable and safe when gliding. If you are tired of the trouble of renting equipment, or want to upgrade your sports experience, then it is time to choose a HJdeck Surf Traction Mat that is exclusive to you! Your board mat must be suitable for you! When choosing a board mat, you need to consider the following factors: Sports type: Different sports such as surfing, paddle boarding, windsurfing, etc. have different requirements for board mats. Board size: Longboards, shortboards, and SUP boards have different board mat designs and sizes. Personal preference: Do you like soft cushioning or strong grip? Different materials and textures will bring different foot feel. HJdeck Surf Traction Mat uses high-density EVA foam and special anti-slip patterns, which can provide excellent stability and comfort whether it is fierce turns when surfing or standing on the paddle board for a long time. The board mat matches your water sports scene Surfing: Strong grip is required to ensure that the feet do not slide during high-speed gliding and sharp turns. Paddle board (SUP): A wide and cushioned board mat is required to reduce fatigue from standing for a long time. Windsurfing: Wear-resistant and waterproof materials are required to adapt to the impact of sea water and wind and waves. HJdeck's board mat series covers a variety of sports needs and is suitable for different board types, so that you can be as stable as a rock in any water sport. Advantages of HJdeck Surf Traction Mat ✔ Super strong grip: The unique diamond texture design can firmly fix your feet even in slippery conditions.✔ Comfortable cushioning: Highly elastic EVA material reduces the pressure on the feet during long-term exercise.✔ Durable and UV-resistant: UV-resistant material, not easy to age and fade after long-term use.✔ Easy to install: Self-adhesive backing design, easy to fit your sports board, no complicated operation required. How to choose your exclusive board mat? Try it out: Go to a professional water sports store to experience the feel of different board mats. Adapt to the board type: Make sure the size of the board mat matches your sports board to avoid being too large or too small. Consider the second-hand market: If your budget is limited, you can look for a good second-hand HJdeck board mat. You can't buy happiness, but you can buy a board mat that makes you play more happily! 🏄♂️ Buy HJdeck Surf Traction Mat now to make your water sports more stable, more comfortable, and more enjoyable!

Jet skis are about speed, agility, and thrills—but without proper hull protection, your precious watercraft can quickly show scratches, scuffs, and wear and tear. EVA foam traction pads (also known as jet ski traction pads or side traction pads) are one of the best ways to protect your investment and improve performance and comfort. Why Your Jet Ski Needs EVA Foam Traction Mats 1. Protect Your Hull from Scratches & Damage Jet skis are subject to constant traffic, gear placement, and exposure to water, sand, and UV rays. Over time, this can cause scratches, scuffs, and even structural wear to the deck. EVA foam traction pads act as a protective barrier, absorbing impact and preventing direct damage to the hull. Not only does this keep your jet ski looking new, it also helps maintain its resale value. 2. Prevent Slipping & Improve Safety It's no secret that wet jet ski decks are extremely slippery, especially on tight turns or in choppy waters. The non-slip EVA foam pads provide superior grip, keeping your feet firmly planted even in wet conditions. This reduces the risk of falls and injuries, making your ride safer and more enjoyable. 3. Enhance Comfort for Longer Rides Standing or kneeling for hours on hard, slippery surfaces can lead to fatigue and discomfort. The cushioning properties of EVA foam absorb the impact of waves, reducing stress on joints and muscles. This makes long rides more comfortable, whether you're cruising or maneuvering at high speeds. 4. Improve Control & Performance A secure footing means you have better control over your jet ski. The textured surface of the EVA foam pads enhances traction for sharper turns, faster acceleration, and a smoother ride—especially in choppy waters. Many professional water skiers consider traction pads to be as important as an engine upgrade when it comes to improving performance. 5. Resists Harsh Marine Conditions Premium EVA foam mats are able to withstand saltwater, UV rays, and extreme temperatures without degradation. Unlike cheap rubber mats that crack or fade, marine-grade EVA foam mats are durable and built to last. Choosing the Best EVA Foam Traction Mats for Your Jet Ski Not all traction mats are created equal. Here are a few things to keep in mind when choosing the right traction mat: ✔ Material Quality Marine-grade EVA foam is waterproof, UV-resistant, and durable. Avoid cheap foams that may contain harmful chemicals like formamide or ammonia. ✔ Thickness & Cushioning Thicknesses between 5mm and 8mm provide a good balance between comfort and durability. Thicker pads (10mm+) provide additional cushioning but may affect the feel for aggressive riders. ✔ Grip Pattern Diamond, hexagonal or embossed patterns provide the best anti-slip properties. Some brands offer customizable designs for a personalized look. ✔ Easy Installation The peel-and-stick adhesive backing makes installation easy. For best adhesion, make sure the deck is clean and dry before use. ✔ Custom Fit vs. Universal Sheets Pre-cut pads are designed for specific models to ensure a perfect fit (e.g. Yamaha, Sea-Doo, Kawasaki, Honda). Universal EVA foam sheets can be cut to fit any jet ski, but will require custom cutting. Universal side/gunnel traction pads can fit any jet ski or can be custom made to your own size. HJDECK – Offers customizable designs and provides model-specific traction mats for Yamaha and other brands. Protect Your Jet Ski & Ride Better Investing in EVA foam traction pads is one of the smartest upgrades you can make for your jet ski. Not only do they protect your hull from damage, they also improve safety, comfort, and performance, making every ride smoother and more enjoyable. Whether you're a recreational rider or a performance enthusiast, a high-quality traction pad will extend the life of your jet ski while giving you the confidence to push your limits on the water. Ready to upgrade? Check out the best EVA foam jet ski pads today and take your riding to the next level!

At HJDeck, we thrive on turning unique ideas into high-performance realities. Recently, a WaveRunner owner approached us with a challenge: design a custom set of two-piece gunnel traction pads for his 2022 Yamaha FX SVHO Limited that would fit seamlessly over the existing hull cleats. The result? A perfect blend of form, function, and customer collaboration. Vision: The Perfect Combination of Stylish Design and Excellent Grip The goal was clear: create traction pads that enhanced control during high-speed maneuvers without disrupting the WaveRunner’s sleek aesthetics. The customer wanted pads placed forward and behind the cleats, ensuring secure foot placement while maintaining the jet ski’s streamlined profile. The customer measured the dimensions at the motorboat dealer, marked them on a file, and sent them to us based on the 3D scans provided by the dealer. Our designers drew the design of the side of the FX SVHO based on the dimensions and scans provided by the customer. The side profile of the Limited is accurate to the millimeter level. Version 1 Collaboration in Action After sharing the initial prototype, the customer emphasized the importance of rounded design and seamless edges—no jagged lines or bulk. We iterated on the design to ensure the pads looked like a factory upgrade, not an afterthought. Version 2 The Final Product: "The Cut Looks Great!" When the customer received their custom HJDeck traction pads, their feedback was instant:“We’ve received the gunnel traction pad today (as shown in the attached photo), and the cut looks great! The precision is exactly what we needed for our WaveRunner.”   The two-piece set installed effortlessly with marine-grade adhesive, hugging the curves of the gunnel while providing unmatched grip. The laser-cut edges ensured a flawless fit around the cleats, proving that customization doesn’t mean sacrificing aesthetics. Why Choose HJDeck for Your Jet Ski Upgrades? This project underscores our commitment to: Bespoke Design: No “one-size-fits-all” compromises.Premium Materials: Built to endure harsh marine environments.Customer-Driven Process: We listen, refine, and deliver. Whether you’re upgrading a 2022 FX SVHO Limited or an older model, HJDeck’s custom solutions ensure your watercraft performs—and looks—its best. Same model Jet Ski Traction Mat: Yamaha FX, HO, SVHO, LTD 2019-2023 Customized Jet Ski Traction Mats Ready to Transform Your Ride? Inspired by this project? Contact HJDeck or DM us to start designing your perfect jet ski upgrade. Let’s make waves together! HJDeck – Engineered for Adventure.

Why You Need a Reliable Water Sports Traction Pad Supplier? As a professional water sports equipment procurement expert, you know the importance of high-quality traction pads in customer experience. Traction pads for surfboards, SUPs and other water sports equipment not only affect comfort, but also directly affect safety. As a professional water sports traction pad manufacturer, HJdeck provides wholesalers and retailers with cost-effective and stable supply solutions to enhance your product competitiveness. Five Key Factors to Consider When Choosing an HJdeck Traction Pad 1. Comprehensive Product Range HJdeck's proprietary diamond-pattern design provides 40% better traction than standard pads. Complete product line from entry-level to professional-grade. 2. Outstanding Product Performance Patented diamond-shaped anti-slip design improves grip by 40%. High-density EVA material extends product life by 30%. UV-resistant treatment for excellent anti-aging performance. 3. Flexible Supply Solutions Provide OEM/ODM customization service. Minimum order quantity is 500 pieces to meet various purchasing needs. 15-day fast delivery cycle to ensure sufficient inventory during peak season. 4. Guaranteed Profit Margins Competitive wholesale pricing with volume discounts. Marketing materials and display solutions included. 5. Complete Quality Certifications Passed ISO9001 quality management system certification. Complies with EU CE safety standards. 12-month quality guarantee. Every HJdeck Surf Traction Mat undergoes thorough inspection before shipping.   Procurement Support & Services • Sample Policy: Free samples are provided, just pay for the shipping cost.• Payment Method: Accept T/T, L/C and other payment methods• Logistics Solution: Sea/Rail/Air• After-sales Service: Dedicated Account Manager provides end-to-end support Contact HJdeck Sales Team Now for Latest Quotations & Promotions! 📧 eric@hjdeck.com🌐 www.hjdeck.com

Why Marine Grade EVA Foam Is the Gold Standard? When it comes to high-performance surfboard traction pads, marine grade EVA foam outperforms alternatives like cork and rubber. Designed for harsh ocean conditions, this advanced material offers superior grip, cushioning, and durability, making it the top choice for pro surfers and ocean enthusiasts. In this deep dive, we’ll explore what makes marine grade EVA unique, how it goes beyond standard EVA, and why it’s the ultimate choice for surfers who demand reliability in any condition. What’s so Special About Marine Grade EVA Foam? Designed to meet the demands of the ocean Not all EVA foams are created equal. Marine grade EVA is specially treated to enhance:✔ Saltwater resistance– prevents damage from prolonged exposure.✔ UV protection– Prevents fading and hardening in the sun.✔ Enhanced density– Maintains cushioning without being too soft.✔ Mildew resistance– Stays fresh even with frequent use. Marine-grade EVA lasts 2-3 times longer than standard EVA and has better grip in wet conditions. Key Benefits of Marine-Grade EVA Grip Pads ① Unmatched Comfort & Responsiveness Shock-absorbing pad reduces foot fatigue during long sessions. Flexible yet supportive for precise board control during tight turns. ② Superior Wet/Dry Traction Deep grooves and diamond pattern effectively channel water for continuous grip. Textured surface slip-resistant even in rough waves. ③ Durable Won't delaminate like cheaper EVA moisture-proof pads. Withstands extreme temperatures (hot deck/cold water). ④ Customization options Available in high-visibility colors for safety. Can be laser cut for customized designs/logos. Marine-Grade EVA vs. Other Materials Feature Marine EVA Standard EVA Cork Rubber Saltwater Resistance ★★★★★ ★★☆☆☆ ★★★★☆ ★★★★☆ UV Resistance ★★★★★ ★★☆☆☆ ★★★★☆ ★★★★☆ Grip When Wet ★★★★☆ ★★☆☆☆ ★★★☆☆ ★★★★★ Comfort ★★★★★ ★★★★☆ ★★★☆☆ ★★☆☆☆ Eco-Friendliness ★★☆☆☆ (Recyclable) ★★☆☆☆ ★★★★★ ★★★☆☆   Key Points: Marine EVA outperforms standard EVA in durability and performance, while providing better comfort than rubber or cork. Who Should Use Marine Grade EVA Surfing Pads? ✔ Shortboard surfers - sensitive flex for fast gliding and carving. ✔ Big wave surfers - reliable grip when it counts. ✔ Travel surfers - for a variety of water temperatures/conditions. ✔ Comfort-conscious surfers - for all-day surfing. Pro Tip: Pair with a parabolic arch bar for extra leverage. Maintenance Pro Tips To maximize the life of your Ocean EVA Surf Pad: 1. Rinse with clean water after each surfing session. 2. Keep out of direct sunlight for extended periods of time when not in use. 3. Scrub monthly with mild soap to remove salt buildup. 4. Store vertically to avoid unnecessary stress on adhesive. Hjdeck Custom Premium Marine-Grade EVA Pads At Hjdeck, we specialize in fully customizable marine-grade EVA foam traction pads for surfboards, SUPs, and all water sports. Using CNC cutting and laser engraving, we offer unlimited design options—colors, patterns, logos, and textures—to match your style.  Our high-performance, UV-resistant pads provide superior grip and durability while allowing complete personalization. Stand out on the waves with your unique design! Why Marine-Grade EVA Reigns? While cork and rubber have limited applications, marine-grade EVA foam offers the ideal balance of: ~ High-Performance Grip ~ All-Weather Comfort ~ Waterproof Durability For surfers who refuse to compromise, upgrading to marine-grade EVA is a game-changer. Ready to experience something different? Check out our recommended marine-grade EVA traction pads: Custom Surf Traction Pad

Custom black & green diamond EVA mats for 2015 Sea-Doo Wake Pro – praised for perfect fit & sporty style! Quick 15-day delivery, 5-year warranty, and share-worthy results.

Custom EVA marine flooring for 2024 Monterey 224 FS earns praise! Fast latch revision & flawless fit. Explore our 3-week turnaround, CAD precision, & eco-friendly designs.

At the 27th China (Shanghai) International Boat Show (CIBS 2025), HJDECK emerged as a leader in sustainable marine solutions with its cutting-edge EVA foam flooring, aligning with the event’s theme “Green Navigation, Intelligent Transformation”. As a self-owned factory with 12 years of expertise, HJDECK showcased its innovative EVA materials, designed to reduce vessel weight, enhance durability, and drive the maritime industry toward a carbon-neutral future.

Hjdeck Dash Pockets keep gear secure on boats, benches & more! Heavy-duty adhesive, sleek colors. Peel, stick, go! Shop or customize now.

Introduction to Surface Texture Options Common Texture Types: Brushed texture: Suitable for most boats, non-slip. Anti-slip granular (Heat embossing dots) texture: suitable for high-humidity areas (such as pool decks), providing stronger friction resistance. Functional Benefits of Textures: Anti-slip, scratch resistance, fingerprint resistance, etc. Texture Implementation Techniques: ​Mold pressing: suitable for large-scale production, low cost. ​Laser engraving: suitable for small-batch customization, can achieve complex textures (such as brand-specific anti-slip textures). Creative Pattern Design and Implementation ​Drainage guide groove: Combined with the groove surface to optimize the drainage path and improve safety. Anti-slip signs: warning patterns or directional arrows are carved in specific areas (such as stairs). Natural elements: such as ocean-themed waves and shell patterns, which fit the marine scene. ​Brand-specific patterns: Companies can customize embossed patterns with LOGO or cultural symbols. Branding scheme for logo engraving design ​Laser engraving: Suitable for fine logos, with high clarity and durability. CNC engraving: CNC machine engraving to achieve 3D logos, with more obvious touch (suitable for high-end brand needs). ​Corner Logos: Subtle branding at sheet edges, preserving aesthetics. ​Central Display: Bold logos at the center for visual impact. Custom Colors Common/Hot-selling Color CombinationsYou can freely combine colors according to your needs. ​Thickness Variations Choose from 5mm to 15mm sheets to balance cushioning and stability. Thicker options are ideal for high-traffic areas like cockpits. Commonly used designs are 6mm (two layers) and 9mm (three layers). Customization process 1. We already have drawings After selecting the part of the mat you need, choosing the color and texture, we will send you the renderings and arrange production after checking the size. The production process is expected to take 5 working days, and delivery to most areas is expected to take about 7-15 days. 2. We don't have drawings ① If you have a CAD file of your boatPlease send us the file in AI/PDF/DXF/CAD format, we will check it and give you an accurate price. ② If you don't have the CAD file of your boat Customer Cases See some of our customers drawing templates and having us engrave them successfully. 2024 Ranger RB 200 2008 Bayliner Element F21 Ready to Transform Your Deck? Contact Hjdeck Boat Flooring today for a ​sample and experience how their EVA foam flooring combines innovation with craftsmanship.

Learn how A.J. replaced the worn flooring on his Stratos Bass Boat with durable, waterproof Closed Cell Foam Pads. Discover why this material is the perfect choice for boat repairs, offering comfort, safety, and longevity.

See how custom Hjdeck EVA foam flooring upgraded a 2024 Ranger RB 200—anti-slip, durable, and sleek. Full process from template to final install!

Upgrade your vessel with custom EVA foam boat mats offering Seadek-grade durability, ISO-certified anti-slip safety, and EU/US compliance. Reduce fuel costs by 18% with hydrodynamic designs + 3-year warranty. Full customization from template to delivery.